Quality Engineers

Technical Description: The apparatus consists of three pipelines emerging out from a common manifold. One pipe line contain a Venturimeter, second contains an Orifice and third pipe line contains a Rota meter. The pressure tapings from the Venturimeter and Orifice meter are taken to differential manometer to measure pressure difference. The Venturimeter, Orifice meter and Rota meter are connected in parallel and any one of them can be put in operation by operating valves provided at the downstream. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank & stop watch.

LEARNING OBJECTS/EXPERIMENTATION:

• To determine the co-efficient of discharged through Venturimeter and orifice meter.
• To measure discharge through Venturimeter, Orifice meter and Rotameter
• To calibrate the Rotameter.

REQUIRMENT FOR OPERATION: Electricity supply: Single Phase, 220 V AC, 50 Hz, 5-15 amp combined socket with earth connection.Water Supply (Initial Fill).Floor Drain required.Floor Area Required: 1.5 m x 0.75 m.

TECHNICAL SPECIFICATION:

• Venturimeter: Material Clear Acrylic compatible to 1 inch Dia. Pipe.
• Orificemeter: Orifice plate made of Stainless Steel and housing made of Clear Acrylic compatible to 1 inch Dia. Pipe.
• Rota meter: Compatible Range. Eureka makes.
• Water Circulation: FHP Pump, Crompton makes.
• Flow Measurement: Using Measuring Tank (Capacity 25 ltrs.) and Electronic Stop Watch.
• Sump Tank: Capacity 50 Ltrs.
• Control Panel Comprises of: Standard makes On/Off Switch, Mains Indicator, etc.
• Instruction Manual: An ENGLISH instruction manual will be provided along With the Apparatus.
• Tanks will be made of Stainless Steel.
• The whole set-up is well designed and arranged in a good quality painted structure.

Control Panel:

• Standard make on/off switch, Mains Indicator etc.

Scope of Delivery:

• 1 Self-contained VENTURIMETER, ORIFICEMETER & ROTAMETER TEST RIG Apparatus
• 1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-20 Days
• Packaging Details: Safe Carton

We offer high-quality Flow-Through Orifice And Mouthpiece to our valuable customers. The offered apparatus is widely used for determining the critical Reynolds number of a fluid flowing through the coil. In addition to this, the apparatus is also used for determining the friction factor for a flow of water through helical coil.

Description:
It consists of a tank provided with inlet supply diffuser, overflow outlet. Provision for fitting Orifice or Mouthpiece at the same position is provided. An arrangement is done to a very head and keep it constant at desired level. A Hook/pointer gauge arrangement for measuring X-Y coordinates of Jet Trajectory is also fitted. The set-up can be connected to Hydraulic Bench by flexible pipe line.

Experimentation:

• To determine the coefficient of discharge of different Orifice and Mouthpiece.

Utilities required:

• Hydraulic Bench.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-20 Days
• Packaging Details: Safe Carton

We are counted among the most prominent manufacturers, traders and exporters of high quality Impact of Jet Vanes. Designed in compliance with industry leading parameters, it is used to study the forced developed of a jet of water on different surfaces and to compare it with momentum theory. Offered set up consists of visible test enclosure, supply tank, measuring tank and pump for closed loop water circulation.

Technical Description:

• The setup consists of a two sided clear fabrication section. Water is fed through a nozzle and discharged vertically to strike a target carried on a stem which extends through the cover. A weight carrier is mounted on the upper end of the stem. The dead weight of the moving parts is counter balanced by a compression spring. The vertical force exerted on the target plate is measured by adding the weights supplied to the weight pan until the mark on the weight pan corresponds with the level gauge. A total of two targets are provided, a flat plate and a hemispherical cup.

Learning Objectives/Experiments:

• To measure the force developed by a jet of water impinging upon a stationary object and comparison with the forces predicted by the momentum theory

Required for Operation:

• Hydraulic Bench

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-30 Days
• Packaging Details: Safe Carton

Quality Engineers holds specialization in the manufacturing, trading and exporting of high quality Meta Centric Height. This apparatus is manufactured under strict supervision, using finest quality raw materials that have been sourced from authentic vendors. Offered apparatus is appreciated around the globe for accurate measurement, simple functionality and longer function life.

Technical Description:

• Determines the metacentric height of a floating body and height variation with tilt angle. Rectangular pontoon. Center of gravity can be moved sideways by moving horizontal jockey weight, and vertically via an adjustable vertical weight on mast. Tilt angle is indicated by a plumb bob on attached scale.

Learning Objectives/Experiments:

• Determination of the metacentric height and position of the metacentric height with angle of heel of ship model

Required for Operation:

• Water supply Tap water connection
• Floor Area with Drain facility

Other Details:

• The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure
• Horizontal Guide Bar for aliding weight and Removable Strips, Graduated arc with Pointer with moveable hanger And set of weights

Scope of Delivery:

• Self Contained Metacentric Apparatus
• Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-30 Days
• Packaging Details: Safe Carton

Very easy to operate, install and maintain, the offered Forced Vortex Apparatus is highly user friendly in nature. Widely used for the purpose of providing a smooth rotational flow of liquid, the offered product is asked for in the market. Manufactured by us in compliance with the set industrial norms and guidelines and is provided to clients at a market leading rate, the offered product is one of the best that is available.

Technical Description:

• The experimental set up consist of a circular transparent cylindrical tank, which four circumferential jets have been placed along the circumference of the cylinder near its bottom which helps in the formation of free vortex. It is assumed that the torque exerted by these jets is negligible. The Orifice is reducing bush so that a reduced diameter can be investigated. The plate can also be rotated with the help of a variable speed motor so that the cylinder rotates about its vertical Axis with the help of a V belt and forced vortex is formed. Conditions wear allowed to steady state and the depth of flow at any particular point was observed not to change over a period of time. The experimental procedure involves measurement of resulting free surface that represents the variation of the sum of the pressure and datum head.

Learning Objectives/Experiments:

• To visualize the forced & free vortex phenomenon
• To plot the shape of vortex profile i.e. vertical height vs horizontal radius.

Required for Operation:

• Water Supply
• Drain

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-30 Days
• Packaging Details: Safe Carton

The set-up consists of a cylindrical test section filled with pourous medium. Pressure tappings are provided in the test section to measure the pressure drop with the help of differential manometer. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and bypass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-30 Days
• Packaging Details: Safe Carton

Quality Engineers is counted among the listed manufacturers, wholesalers and exporters of premium quality Bernoulli’s apparatus. Offered apparatus is precisely manufactured under strict supervision in compliance with industry laid parameters. These units consist of a rectangular transparent flow section through which water is to be flown. The velocity of water changes across the sectional area of channel changes.

Technical Description:

• The setup is designed to verify Bernoulli's Theorem experimentally Set up consists of a one piece clear acrylic test section with convergent and divergent part sections, supply thank, measuring tank, inlet water tank and pump for closed loop water circulation. The test section is connected to Piezometer Tubes through pressure tapping at different locations on the section to demonstrate the Bernoulli’s Theorem. The flow rate of water is measured using measuring tank and stop watch provided.

Learning Objectives/Experiments:

• To verify Bernoulli's Theorem experimentally

Required for Operation:

• Electric supply 0.5 kW, 220V AC, Single Phase
• Water supply Tap water connection
• Floor Area with Drain facility
• The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure

Control Panel:

• Standard make On/Off switch, Mains Indicator etc.

Scope of Delivery:

• 1 Self Contained Bernoullis Apparatus
• 1 Instruction Manual consisting of experimental procedures, block diagram etc.

Being one of the leading manufacturers and exporters of these Losses Due To Pipe Fitting , Sudden Enlargement & Contraction, we never compromise with quality. Offered to the clients at a very reasonable price, the offered product is one of the first choices. Determining the losses caused because of pipe fittings, the level of accuracy it offers is unmatched. Further, the product is quite sturdy, resistant to corrosion and highly durable.

Description:

• The set up consists of a 1/2 bend and elbow, a sudden expansion & sudden contraction fitting from 15mm to 25mm, ball valve and gate valve. Pressure tapings are provided at inlet and outlet of these fittings under test. A differential manometer fitted in the line gives pressure loss of individual fittings. The set-up can be connected to Hydraulic Bench by flexible pipe line.

Learning Objectives/Experiments:

• To determine loss of head in the fittings at various water flow rates.
• To determine the loss co-efficient for the pipe fittings.
• Comparing the Pressure drop across each device.

Required for Operation:

• Hydraulic Bench

Other Details:

• The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure

Control Panel:

• Standard make On/Off switch, Mains Indicator etc.

Scope of Delivery:

• 1 Losses Due To Pipe Fittings Apparatus
• 1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-30 Days
• Packaging Details: Safe Carton

"PIPE SURGE & WATER HAMMER APPARATUS"(With Data Logging Facility)
Technical Description The equipment is self-contained and is close circuit system. It consists of two test sections, one for pipe surge and other for water hammer phenomenon. The whole system incorporates a head tank, measuring tank, sump tank,circulating pump, a lever operated gate valve and flow control valve. The water enters the test pipe via the constant head tank and discharges into the measuring tank.Two electronic Pressure sensors with current output of 4 -20mA are installed on the unit.The present set-up has a facility to interface the system with computer which enables to log the experimental data using computer. The educational software and data-logging package has been developed for unit. The software environment base is of Labview of NATIONAL INSTRUMENTS, USA. This software is compatible to interfacing unit designed by K. C. Engineers. This software package provides a comprehensive educational software environment within which the investigations can be performed. This software is capable to tabulate the sample readings according to the requirement of experiment under study and results obtained can be compared. The real time data acquisition can be done by interfacing the set-up with computer using software. Software allows the user to have control on data logging, printing the stored data, preparing spread sheets in Excel etc.

LEARNING OBJECTS/EXPERIMENTATIONTo demonstrate the surge phenomenon in pipe.To demonstrate the oscillatory characteristics of surge shaft.
REQUIRMENT FOR OPERATION Electricity Supply Single phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection.Water supply (Initial Fill)Floor Drain required.Computer P-IV, with DVD drive, Windows 7 and MS Office preloaded. One USB slot free for Hardware.
TECHNICAL SPECIFICATION Test section material stainless steel Size 20 mm ID (approx), length 3m (approx.).Surge shift material clear acrylic. Size 40mm ID (approx), Height 800mm(approx) with graduated scale.Water circulation centrifugal pumpFlow measurement flow sensor output 4-20 MA. Constant head tank material stainless steel, suitable capacity. Sump tank material stainless steel, suitable capacity. Pressure measurement pressure sensor 0-7 bar, output 4-20 mA (for water hammer) Level measurement level sensor, output 4-20 mA (for pipe surge) Control panel consists of standard make on/off switch , mains indicator, etc. An ENGLISH instruction manual will be provided along with the ApparatusThe whole set-up is well designed and arranged on a rigid structure painted with industrial PU Paint.
Control PanelStandard make on/off switch, Mains Indicator etc.
Scope of Delivery1 Self-contained "PIPE SURGE & WATER HAMMER APPARATUS" Apparatus1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-30 Days
• Packaging Details: Safe Carton

The equipment is mounted on a steel-framed bench fitted with castors. A variety of measuring devices is incorporated either fastened to the back of the bench or free-standing. Water is stored in a tank situated on the lower shelf of the bench. The water can be transferred by a pump to an elevated open storage tank connected to a number of glass tubes for free surface studies, or to a recessed into the working surface so that benchtop experiments may be conducted without spillage. All excess water is returned to the storage tank via the sink drain.

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 days

The apparatus consists of a pipeline emerging out from a common manifold. The pressure tapings from the Venturimeter are taken to differential manometer to measure pressure difference. Present setup is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.

LEARNING OBJECTS/EXPERIMENTATION:

➢ To demonstrate the use of Venturimeter .
➢ To determine co-efficient of discharge through Venturimeter.
➢ Electricity Supply: Single Phase, 220V AC, 50 Hz, 5-15 amp combined socket with earth connection. REQUIRMENT FOR OPERATION:

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 309-40 days

The apparatus consists of a pipeline emerging out from a common manifold. This pipe line contains an Orifice. The pressure tapings from the orifice meter are taken to differential manometer to measure pressure difference. The flow can also be regulated by the valve provided. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.

LEARNING OBJECTS/EXPERIMENTATION:

➢ To demonstrate the use of Orifice meter as flow meter.
➢ To determine co-efficient of discharge through Orifice meter.
➢ Electricity Supply: Single Phase, 220V AC, 50 Hz, 5-15 amp combined
➢ socket with earth connection.

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30 days

The present set-up is a self-contained ,water re-circulating unit provided with a top tray and a sump tank. Various hydraulics experiments can be conducted on this set up. AFHP Centrifugal Pump is fitted for water circulation. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stopwatch. Water collected on the top tray from experimental set-up ,drains and return to sump tank.

The set up consists of a 1/2” bend and elbow, sudden expansion & sudden contraction fitting from 15 mm to 25 mm, ball valve and gate valve. Pressure tapings are provided at in let and outlet of these fitting sunder test. A differential manometer fitted in the line gives pressure loss of individual fittings. The set-up can be connected to Hydraulic Bench by flexible pipe line.

LEARNING OBJECTS/EXPERIMENTATION:

➢ To determine loss of head in the fittings at various water flow rates.
➢ To determine the loss co-efficient forth pipe fittings.
➢ Comparing the Pressured rop across each device

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 days

The equipment is designed and fabricated to demonstrate the Bernoulli's theorem. It consists of a test section made of acrylic. It has convergent and divergent sections. Pressuret a pings are provided at different locations in convergent and divergent section. The set-up can be connected to Hydraulic Bench with flexible pipe line.

LEARNING OBJECTS/EXPERIMENTATION:

➢ To verify Bernoulli's Theorem experimentally.
➢ To plot the hydraulic gradient line.
➢ To plot the Total energy line Vs distance. 

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 days

A Pitot tube is used to measure the local velocity at a given point in the flow stress. A Pitot tube of standard design made of copper /Stainless Steel is supplied and is fixed below a vernier scale. The vernier scale is capable to measure the position of Pitot tube in transparent pipe section. The pipe has a flow control valve to regulate the flow. An U-tube manometer is provided to determine the velocity head.

LEARNING OBJECTS/EXPERIMENTATION:
➢ To find the point velocity at the center of a tube for different flow rates of meter and calibrate the pitot tube.
➢ To find the co-efficient of Pitot tube.
➢ To study the flow distribution in a pipe and estimate the ratio of average velocity to maximum velocity at the center of pipe for different flow rates.
➢ To plotvelo city profile across the cross section of pipe for different Reynold's number. 

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 Piece

 The set –up consists of different pressure measurement devices fitted in a pipe line, in which an Orifice is fitted to create the pressure difference. The students can have good in sight of the devices. The set-up can be connected to Hydraulic Bench with flexible pipe line.

LEARNING OBJECTS/EXPERIMENTATION:
➢ To demonstrate the working of different pressure measuring devices.
➢ To measure the pressure practically by different pressure measuring devices.

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 days

The apparatus consists of a pipe lines that contains a Venturimeter. The pressure tapings from the Venturimeter are taken to differential manometer to measure pressure difference. The flow can also be regulated by the valves. The set-up can be connected to Hydraulic Bench with flexible pipe line.

LEARNING OBJECTS/EXPERIMENTATION:
➢ To demonstrate the use of Venturimeters as flow meters.
➢ To determine the co-efficient of Discharge (cd). 

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 days

The Metacentric Height Apparatus unit can be used to study the stability of a floating body and to determine the metacentre graphically. In addition, the buoyancy of the floating body can also be determined. The experiment is easy to set up and is particularly suitable for practical work in small groups.The experiment is conducted in a tank filled with water. A transparent body with a rectangular frame cross-section is used as the floating body. Clamped weights that can be moved horizontally and vertically make it possible to adjust the centre of gravity and the heel.

 

 

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 days

Quality Engineers offers superior quality Discharge Through Venturimeter & Orificemeter Meter Apparatus at the most affordable market price. This apparatus is used to determine the co-efficient of discharged through different flow meters like the venturimeter. Offered apparatus is hugely appreciated among the clients for hassle-free installation, simple operation and optimum performance. Furthermore, our offered apparatus is also demanded for its dimensional accuracy.

Technical Description:

• The apparatus consists of two pipelines emerging out from a common manifold. One pipe line contain a Venturimeter and other contains an Orifice. The pressure tapings from the Venturimeter and orifice meter are taken to differential manometer to measure pressure difference. The Venturimeter and Orificemeter are connected in parallel and any one of them can be put in operation by operating valves provided at the downstream. The flow can also be regulated by these valves. The set-up can be connected to Hydraulic Bench with flexible pipe line.

Learning Objectives/Experiments:

• To determine the co-efficient of discharged through Venturimeter
• To measure discharge through Venturimeter as flow meters

Required for Operation:

• Water supply Tap water connection ” BSP Distilled water @ 60 liters (optional)
• Floor Area with Drain facility
• The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure

Control Panel:

• Standard make On/Off switch, Mains Indicator etc.

Scope of Delivery:

• 1 Self Contained "Discharge Through Venturimeter & Orificemeter" Apparatus
• 1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-30 Days
• Packaging Details: Safe Carton

It consists of a tank provided within let supply diffuser, over flow outlet. Provision for fitting Orifice or Mouthpiece at the same position is provided. An arrangement is done to vary head and keep it constant at desired level .A Hook/pointer gauge arrangement for measuring X-Y co-ordinates of Jet Trajectory is also fitted. The set-up can be connected to Hydraulic Bench by flexible pipe line.

LEARNING OBJECTS/EXPERIMENTATION:

➢ To determine the co-efficient of discharge of different Orifice and Mouthpiece.

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 days

The apparatus consists of a pipe lines that contains a Venturimeter. The pressure tapings from the Venturimeter are taken to differential manometer to measure pressure difference. The flow can also be regulated by the valves. The set-up can be connected to Hydraulic Bench with flexible pipe line.

LEARNING OBJECTS/EXPERIMENTATION:

➢ To demonstrate the use of Venturimeters as flow meters.
➢ To determine the co-efficient of Discharge (cd). 

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 days

Quality Engineers among the trusted names engaged in the manufacturing, trading and exporting of best quality Reynolds Apparatus. The set-up we offer is basically a self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Our professionals manufacture this apparatus in accordance with the industry set parameters using best quality raw materials. This apparatus is used to measure flow rate and is available at affordable market prices.

Technical Description:

• Reynolds Apparatus is used to study laminar, transitional, and turbulent flow. Features a transparent tank with an adjustable overflow pipe. Water admitted via diffuser and stilling materials, discharged via bellmouth transparent tube with flow control valve. Flow rate measured by hydraulics bench or measuring cup. Dye injection system for flow pattern observation.

Learning Objectives/Experiments:

• To determine the Reynold's number and hence the type of flow either laminar or turbulent.
• The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure.

Control Panel:

• Standard make On/Off switch, Mains Indicator etc.

Scope of Delivery:

• 1 Self Contained "Reynolds Apparatus"
• 1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-30 Days
• Packaging Details: Safe Carton

Our company is counted among the leading manufacturers and traders of high-quality Discharge Over Notches. Manufactured using the best quality raw materials under proper supervision, this apparatus is used for the purpose of testing and demonstrating the industrial machinery. Offered apparatus is highly demanded in the market for its easy installation, simple functionality and nominal market price.

Experiments:

• To determine co-efficient of discharge using different notches

Utilities Required:

• Water supply Tap water connection BSP Distilled water @ 60 litres (optional)
• Floor Area with Drain facility

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-30 Days
• Packaging Details: Safe Carton

Technical Description:

• The apparatus has been designed to demonstrate the phenomena of cavitation. The present set-up consists of a test section made of acrylic having conversion and diversion section. Pressure tapings at appropriate position are provided. This test section is having one control valve at upstream side to regulate the water flow rate. Two pressure gauges are connected to these taping which give the pressure readout at the time of flow passing through this test section.
• The unit is self-contained close circuit type with sump tank, measuring tank and centrifugal pump. Flow through test section can be regulated with the help provided by-pass and control valve.

Learning Objectives/Experiments:

• To observe the phenomena of cavitation.
• To compare the theoretical and actual pressures at cavitation condition.

Required for Operation:

• Water supply Initial filled.
• Floor drain required.
• The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure

Control Panel:

• Standard make On/Off switch, Mains Indicator etc.

Scope of Delivery:

• Self Contained Cavitation Apparatus
• Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-30 Days
• Packaging Details: Safe Carton

Quality Engineers is regarded among the top most manufacturers, wholesalers and exporters of optimum quality Pitot Tube SetUp. This apparatus is manufactured using the best quality raw materials that have been sourced from authentic vendors. This apparatus is easy to install and used to measure the flow rate. Offered apparatus is appreciated for its compact design, optimum performance and hassle-free operation.

Technical Description:

• A Pitot tube is used to measure the local velocity at a given point in the flow stress. A Pitot tube of standard design made of copper/Stainless Steel is supplied and is fixed below a vernier scale. The vernier scale is capable to measure the position of Pitot tube in transparent pipe section. The pipe has a flow control valve to regulate the flow.

Learning Objectives/Experiments:

• To find the point velocity at the center of a tube for different flow rates of water and calibrate the Pitot Tube.
• To plot velocity profile across the cross section of pipe

Required for Operation:

• Water supply Tap water connection
• Floor Area with Drain facility
• The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure

Control Panel:

• Standard make On/Off switch, Mains Indicator etc.

Scope of Delivery:

• 1 Self Contained "Pitot Tube Set Up" Apparatus
• 1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-30 Days
• Packaging Details: Safe Carton

Technical Description:

The setup consists of 2 pipes of different diameters, which are connected in parallel. Pressure tapings are provided on each pipe to measure the pressure losses with the help of a Differential Manometer. Control valves are fitted on each pipe, which enables to use one pipe at a time for experiment. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve And by-pass valve are fitted in water line to conduct the Experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.

LEARNING OBJECTS/EXPERIMENTATION:

To determine the losses due to fiction in pipes.
To determine the friction factor for Darcy We is back equation.
REQUIRMENT FOR OPERATION:
Water Supply.
Drain.
Electricity 0.5 kW, 220V AC, Single Phase.
Floor Area 1.5 x 0.75 m.

TECHNICAL SPECIFICATION:

Pipe Test Section: (i) Dia ½”, Length : 1m, Material G.I.
(ii) Dia ¾”, Length: 1.25m, Material G.I.
Water Circulation: FHP Pump, Crompton/godrej/G.E makes.
Flow Measurement: Using Measuring Tank with Piezometer, Capacity 25 Ltrs.
Sump Tank: Capacity 50 Ltrs.
Stop Watch: Electronic.
Control Panel Comprises of :
Standard make On/Off Switch, Mains Indicator, etc.
Instruction Manual : An ENGLISH instruction manual will be provided along
with the Apparatus Tanks will be made of Stainless Steel.
The whole set-up is well designed and arranged in a good quality painted structure.

Control Panel:

Standard make on/off switch, Mains Indicator etc.

Scope of Delivery:

1 Self-contained “ LOSSES DUE TO FRICTION IN PIPE LINES” Apparatus
1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 Days

The Centre of Pressure Apparatus has been designed to determine the static thrust exerted by a fluid on a submerged surface and allow comparison of the measured magnitude and position of this force with simple theory.A fabricated quadrant is mounted on a balance arm, which pivots on knife-edges. The knife-edges coincide with the centre of arc of the quadrant. Thus, of the hydrostatic forces acting on the quadrant when immersed, only the force on the rectangular end face gives rise to a moment about the knife-edges. The balance arm incorporates a balance pan for the weights supplied and an adjustable counterbalance. This assembly is mounted on top of an acrylic tank, which may be leveled by adjusting screwed feet. An indicator attached to the side of the tank shows when the balance arm is horizontal. Water is admitted to the top of the tank by a flexible tube and may be drained through a cock in the side of the tank. The water level is indicated on a scale on the side of the quadrant.

LEARNING OBJECTS/EXPERIMENTATION:Determining the centre of pressure on both a submerged or partially submerged plane surface and comparison with the theoretical position.
REQUIREMENT FOR OPERATION: Water Supply : Initial Fill
Drain Bench Area Required: 0.5 m x 0.25 m
TECHNICAL SPECIFICATION: Tank capacity: 5 litres (approx).Distance between suspended mass & fulcrum : 275mmCross-sectional area of quadrant (torroid) : (100 x 100) mm2Total depth of completely immersed quadrant : 160 mm
Height of fulcrum above quadrant : 100 mm
Instruction Manual : An ENGLISH instruction manual will be provided along with the Apparatus
The whole set-up is well designed and arranged in a good quality painted structure.Control Panel:Standard make on/off switch, Mains Indicator etc.
Scope of Delivery:1 Self-contained "CENTER OF PRESSURE APPARATUS" Apparatus1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-20 days
• Packaging Details: safe carton

The present set-up is designed to study the friction head losses through pipes, fittings, and flow metering devices. Four different ID sizes smooth pipes and one artificially roughened pipe is connected in parallel. A valve arrangement is provided to operate the one pipe at a time. Various types of fitting are also fitted with pressure taps to conduct the experiment. Flow meters (Venturimeter and Orificemeter) is also accompanies the set-up. For water circulation and flow rate determination sump tank & measuring tank are provided. The educational software and data -logging package has been developed for this unit. It is compatible to interfacing unit designed by KC Engineers. It provides a comprehensive educational software environment within which the investigations can be performed. This software runs in Windows XP. It is capable to tabulate the samples readings according to requirement of experiment under study and results obtained can be compared. Interfacing the set up with computer using software can do the real time data acquisition. Data can be transferred in Excel Files for further calculations, plotting graphs etc. Software allows the user to have control on data logging, printing the stored data, preparing spread sheets in Excel etc.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-20 days
• Packaging Details: Safe carton

Technical Description

The experimental set up consist of a circular transparent cylindrical tank in which four circumferential jets are placed along the circumference of the cylinder near its bottom which helps in the formation of free vortex. It is
assumed that the torque exerted by these jets is negligible. A pointer can be transversed horizontally & vertically across full diameter of the vessel so that water surface profile can be measure. Both axes contain graduations so
that exact position of the pointer is known. The experimental procedure involves measurement of the resulting free surface that represents the variation of the sum of the pressure head and datum head. An arrangement is provided to drain the vessel.

LEARNING OBJECTS/EXPERIMENTATION

To plot the surface profile of a free vortex by measurement of the surface profile coordinates and to show that total energy is constant throughout vortex.

REQUIRMENT FOR OPERATION

Electricity Supply Single Phase 220 V AC, 50 Hz, 5-15 amp socket with earth connection.
Water Supply (Initial fill).
Drain required.
Floor Area Required 1 m x 1 m.

TECHNICAL SPECIFICATION

Cylinder Material Acrylic. Dia. 200 mm (approx).
Height200mm approx
Water Circulation FHP Pump, Crompton make.
Flow Measurement Using Rota meter.
Sump Tank Made of Stainless Steel, Compatible capacity.

Control Panel Comprises of

Standard make On/Off Switch, Mains Indicator, etc.
An ENGLISH instruction manual consisting of experimental procedures, block diagram etc. will be provided along with the Apparatus
The whole set-up is well designed and arranged on a rigid structure painted with industrial PU Paint.

Control Panel

Standard make on/off switch, Mains Indicator etc.

Scope of Delivery

1 Self-contained "FREE VORTEX APPARATUS" Apparatus
1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 15 piece per quarter
• Delivery Time: 15-20 days
• Packaging Details: safe carton

The lab set up consists of a channel with deepened entry section having sufficient length and width in which water is supplied from the bottom. Required Notch is fitted a to need of this channel. Upstream from the face Notch, a gauge well is provided where a hook gauge is fitted. Arrangement for fixing interchangeable notches is made. Set of different notches like V Notch, Rectangular notch etc. are given for experimentation.

LEARNING OBJECTS/EXPERIMENTATION:

➢ To determine co-efficient of discharge (Cd) through:
➢ V notch (60°&45°).
➢ Rectangular Notch

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 days

The set up consists of 2pipes of different dia, which are connected in parallel. Pressure tapings are provided one a pipe to measure the pressure losses with the help of a Differential Manometer. Control valves are fitted on each pipe, which enables to us one pipe at a time for experiment. The set –up can be connected to Hydraulic Bench by flexible pipe line.

OBJECTS/EXPERIMENTATION:
➢ To determine the losses due to friction in pipes.
➢ To determine the friction factor for Darcy-weirback equation. 

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 days

Technical Description:

The set-up consists of different pressure measurement devices fitted in a pipe line, in which an Orifice is fitted to create the pressure difference. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line.

LEARNING OBJECTS/EXPERIMENTATION:

• To demonstrate the working of different pressure measuring devices.

• To measure the pressure and pressure difference by pressure gauge, single column manometer, U Tube manometer & Inclined tube manometer.

REQUIRMENT FOR OPERATION:

• Electricity Supply: Single phase, 220 VAC, 50 Hz, 5-15 amp. Combined socket with earth connection.
• Water Supply (Initial fill)
• Floor Drain required.
• Floor Area Required: 1.5 m x 0.75 m
• Mercury (Hg) for manometer (750 gm).

TECHNICAL SPECIFICATION:

• Single Well Manometer: Single Tube Type.
• Differential Manometer: U Tube Type.
• Sensitive Manometer. : Inclined Tube Type
• Pressure Gauge. : Bourdon Type
• Water Circulation: FHP Pump, Champion makes.
• Sump Tank: Capacity 60 Ltrs.
• Control Panel Comprises of:
• Standard make On/Off Switch, Mains Indicator, etc.
• Instruction Manual: An ENGLISH instruction manual will be provided along
• With the Apparatus Tanks will be made of Stainless Steel.
• The whole set-up is well designed and arranged in a good quality painted structure.

Control Panel:

• Standard make on/off switch, Mains Indicator etc.

Scope of Delivery:

• 1 Self-contained "STUDY OF PRESSURE MEASUREMENT" Apparatus
• 1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-20 days
• Packaging Details: safe carton

Technical DescriptionThe present set-up is designed to visualize the ideal flow around immersed body. It consists of a flowtable in which flow of water is circulated in between two transparent sheets with a small gap between them. Water is supplied to the table and a colored dye is injected in the inlet of flow at different location. Water from the sump tank is pumped by a centrifugal pump to a calming section for table and after passing through transparent sheet it goes to sump tank. By-pass and flow control valves are provided to regulate the flow.Flow is made laminar by operating inlet control valve for water and it is visualized due to transparent sheet and colour. A small capacity dye tank will be provided for the flow of dye in fluid inlet stream. Any obstacle can be placed between the sheets and change in flow pattern can be visualized. Obstacles of different types will be supplied with the apparatus.
LEARNING OBJECTS/EXPERIMENTATIONTo visualize the ideal flow around the immersed bodies of different types.
REQUIREMENT FOR OPERATIONElectricity Supply single phase, 220 V AC, 50 Hz, 5-15 amp combined socket with earth connection.Water Supply (Initial fill).Floor Drain required.Floor Area Required 1 m x 0.5 m.Chemical Required Dye (KMnO4) - 10 gm
TECHNICAL SPECIFICATIONFlow Table
Length 750 mm (approx.)Width 500 mm (approx.)Material Stainless SteelTransparent Sheets Material Glass/Acrylic (Qty 2 Nos.)Water Circulation FHP Pump Champion/ godrej make.Sump Tank
Capacity 40-50 Ltrs
Material Stainless Steel
Dye Vessel
Capacity 1 Ltrs
Material Stainless Steel
Instruction Manual An ENGLISH instruction manual will be provided alongwith the Apparatus
The whole set-up is in well designed and arranged in a good quality painted structure.
Control PanelStandard make on/off switch, Mains Indicator etc.
Scope of Delivery1 Self-contained "LAMINAR FLOW TABLE" Apparatus1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Delivery Time: 15-20 days
• Packaging Details: safe carton

Technical Description: The apparatus consists of a pipeline that contains one Bend meter. The pressure tapings from the Bend meter is taken to differential manometer to measure pressure difference. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.

LEARNING OBJECTS/EXPERIMENTATION:To demonstrate the use of Bend meter as flow meter.To determine co-efficient of discharge for given Bend meter.

REQUIRMENT FOR OPERATION: Electricity supply: Single Phase, 220 VAC, 50 Hz, 5-15 amp combined socket with earth connection.Water Supply (Initial Fill).Floor Drain required.Floor Area required: 1.5 m x 0.75 m Mercury (Hg) for manometer (250 gm).

TECHNICAL SPECIFICATION: Bend meter : Material Stainless steel Compatible to 1” Dia. Pipe.Water Circulation : FHP Pump, Crompton makeFlow Measurement : Using Measuring Tank (Capacity 25 Ltrs. (approx.))and Electronic Stop WatchSump Tank : Capacity 50 Ltrs. (approx.)Control Panel Comprises of :Standard make On/Off Switch, Mains Indicator, etc.Instruction Manual : An ENGLISH instruction manual will be provided along with the Apparatus Tanks will be made of Stainless Steel.The whole set-up is well designed and arranged in a good quality painted structure.

Control Panel:Standard make on/off switch, Mains Indicator etc.

Scope of Delivery:1 Self-contained “BEND METER TEST RIG” Apparatus1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-20 days
• Packaging Details: safe carton

We are offering a wide range of Nozzle Meter Test Rig to our clientsThe apparatus consists of a Nozzle meter made of stainless steel houses in Acrylic Test Section. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch. LEARNING OBJECTS/EXPERIMENTATION:
 To measure discharge through Nozzle meter.
 To calculate co-efficient of discharge for nozzle meter. 

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-30 Days
• Packaging Details: Safe Carton

The apparatus consists of a pipeline emerging out from a common manifold. This pipe line contains a Rota meter. . Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank & stop watch.

LEARNING OBJECTS/EXPERIMENTATION:
 To measure discharge through Rotameter.
 To calibrate the Rotameter. 

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 days