Quality Engineers

We are offering a wide range of Pressure Drop Through Packed Bed.The set-up consists of a glass column packed with packing material i.e. Rasching rings, SS mesh to support the packing and with the calming section. The pressure drop across packed bed can be measured by a manometer. The apparatus is close circuit type provided with the tank, Pump, necessary piping, valves and Rotameter to measure the flow rate of the fluid. The set-up is fitted on an MS frame and painted with good quality corrosion resistant paint.

Learning Objectives/Experiments

• To study the relationship between the velocity of fluid and pressure drop per unit packed length.
• Standard make on/off switch, Mains Indicator etc.

Scope of Delivery:

• 1 Self-contained "Pressure Drop Through Packed Bed" Apparatus
• 1 Instruction Manual consisting of experimental procedures, block diagram etc.

We offer optimum quality Drag Co-Efficient Apparatus to our valuable customers. Manufactured in compliance with the industry set standards, the apparatus is commonly used for studying the behavior of particle-fluid systems. This apparatus is highly demanded in the market for its impeccable finish and optimum performance.

Technical Description:

• The apparatus has been designed to introduce students to the fundamental characteristics of the behaviour of the particle system, in particular the relationship between the drag coefficient of falling particles and Reynolds number. Particles covering a range of sizes and densities are supplied and the experiments are conducted by allowing single particles to fall through a number of different liquids contained in a vertical glass tube. The rate of fall of the particle is determined by timing their passage between two marks on the walls of the glass tubes. Observation of the particle movement is aided by the provision of a shielded fluorescent tube light mounted on the backboard. Particles can be removed from the bottom of the tubes without the necessity of draining the liquid. A valve system is provided at the bottom of each tube to allow the particles to be removed with the minimum loss of liquid

Learning Objectives/Experiments

• To measure the drag Coefficient and verify Stokes Law.
• To plot the graph between drag coefficient Vs. Reynolds number.
• To study the motion of a solid particle through a liquid.

Scope of Delivery:

• 1 Self-contained "Drag Coefficient" Apparatus
• 1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 5-10 piece
• Delivery Time: 30-40 days

We are offering a wide range of Flow Through Helical Coil Machine. This apparatus offered by us is commonly used to determine the critical Reynolds number of a fluid flowing through the helical coil. Furthermore, these experimental arrangements are commonly used for the purpose of comparing the various pressure drops that take place in helical coils.

Technical Description:
Helical coils are used for heating or cooling in process tanks. When a fluid flows through a curved tube, centrifugal force acting upon the various elements of fluid moving with different velocities causes secondary circulation. Secondary flow results in higher heat transfer characteristics. Further, secondary flow stabilizes the laminar flow leading to a higher critical Reynolds number for transition from laminar to turbulent flow.

Learning Objectives/Experiments

• To determine the critical Reynolds number of a fluid flowing through the coil.
• To compare Pressure drop in helical coil with that in a straight pipe of same length, inside diameter and surface roughness.

Scope of Delivery:

• 1 Self-contained "FLOW THROUGH HELICAL COIL" Apparatus
• 1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 15 pc. per qtr.
• Delivery Time: 15-30 Days
• Packaging Details: Safe Carton

We are offering a wide range of Pressure Drop In Two- Phase Flow Equipment. The Apparatus is designed to study the pressure drop in two-phase flow under different patterns. The set-up consists of a test section, made of Borosilicate Glass to visualize the different patterns. A Centrifugal Pump, with flow control valve and by-pass valve, is provided to supply water to the pipe line. At the outlet, a Separator is provided to separate the air from water. Two Rotameters one each for Air and Water are provided to measure the flow rates.

Learning Objectives/Experiments

• To determine the pressure drop in two phase flow.
• To visualize the flow pattern.

Control Panel:

• Standard make on off switch, Mains Indicator fuse etc.

Scope of Delivery:

• 1 Self-contained "Pressure Drop In Two-Phase Flow" Apparatus
• 1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 5-10 days
• Delivery Time: 30-40 days

We are offering a wide range of Hydrodynamics of Packed Bed (Liquid Hold-Up). The set up is capable of studying the loading and flooding characteristics. It is a packed column packed with Rasching Rings where the Air is counter currently fed to the column. The liquid holdup in the column increases the weight of column and also reduces the effective porosity of packing. This reduction in porosity decreases the gas velocity, increases the pressure drop and changes the value of mass transfer coefficient. The water is fed from the top of the column and loading & flooding characteristic are observed on various flow rates of Air and Water. The apparatus is closed circuit type provided with a suitable capacity tank, pump, necessary pipe lines walls & rotameters for water & air to measure the flow rate of fluids.

Learning Objectives/Experiments

• To study the loading and flooding characteristics in a packed column.

Scope of Delivery:

• 1 Self-contained "Hydrodynamics of Packed Bed (Liquid Hold Up)" Apparatus
• 1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 Days

The set up consists of 3 glass columns. One column is provided with glass beeds for fluidization study. Two columns are packed with different packing’s, i.e. one filled with Rashing Rings and other one is filled with barrels addle. Pressure drop can be measured by manometer. The set up studies in fluidization characteristics and relationship between the velocity of the fluid and pressure dropper unit length. The apparatus is close circuit type provided with suitable capacity tank, FHP pump, necessary pipe line valves and a Rota meter to measure the flow rate of fluid . An valve arrangement is provided too sperate any single column at a time. The set up is fitted on a MS frame painted with good quality paint.

Additional Information:

• Production Capacity: 5-10 Piece
• Delivery Time: 30-40 Days

Upward flow of fluid through a bed of particles is a naturally occurring phenomenon, for example the movement of ground water. Industrial applications include ion exchange, extraction of soluble components from raw materials and other chemical processes. The present set up consists of a glass column of suitable length which is supported on a rigid frame. A rotameter is installed to measure the flow rate of water. A gate valve is installed in the line to control the flow rate of water. A SS tank is provided to store the water and pump sucks the water from the tank and deliver in the line. A bypass valve is provided to bypass the water. A manometer is installed to measure the pressure drop between two points in the column.

Additional Information:

• Item Code: QEMT-630
• Production Capacity: 4
• Delivery Time: 5 DAYS
• Packaging Details: WOODEN